描述
Fuente II filter cartridges are a unique combination of Ultipleat® filter construction and optimized built-in pre-filtration to give longer filter life and lower filtration costs.
The Fuente II filter was developed as a final filter for bottled water. It provides a reliably stable product when applied directly before bottling.
The cartridge is constructed from two layers of hydrophilic Supor® polyethersulfone (PES) membrane. The single open ended (SOE) configuration is designed to fit into sanitary housings to ensure effective microbial stabilization and assembly integrity.
Fuente II filter cartridges are suitable for exposure to repeated cold chemical, hot water and in situ steam sanitization cycles for longer service life.
Features | Benefits |
Cartridges resistant to numerous sanitization cycles |
|
Hydrophilic PES media |
|
Ultipleat filter construction and built-in pre-filtration layer |
|
Individually serialized modules |
|
Multiple adaptor options |
|
Quality
- Cartridges produced in a controlled environment
- Manufactured according to ISO 9001:2015 certified Quality Management System
Food Contact Compliance
Please refer to the Pall website www.pall.com/foodandbev for a Declaration of Compliance to specific National Legislation and/or Regional Regulatory requirements for food contact use.
Specifications
Removal Rating
A technical performance report is available for Fuente II filter cartridges upon request.Materials of Construction
Filter Media | PES |
Support and Drainage | Polypropylene |
Core, Cage, End Cap and Fin End | Polypropylene |
Adaptor | Polypropylene with an internal stainless steel reinforcing ring |
O-ring Seal | Ethylene propylene rubber or Silicone elastomer |
Operating Characteristics in Compatible Fluids1
Maximum Differential Pressure | Operating Temperature |
5.0 bard (72.5 psig) (forward pressure) | 40 °C (104 °F) |
1.0 bard (14.5 psig) (reverse pressure) | 40 °C (104 °F) |
1.0 bard (14.5 psig) (forward pressure) | in-situ steam sterilization |
Sanitization, Sterilization and Cleaning*
Media | Temperature | Cumulative Time/Cycles2 |
Steam | 125 °C (257 °F) | 40 hours /120 x 20 minute cycles |
Hot water | 85 °C (185 °F) | 100 hours / 300 x 20 minute cycles |
Peracetic acid based products (325 ppm of PAA and 1275 ppm of hydrogen peroxide) | Ambient | 400 hours |
*Nitric acid (0.5%) | Ambient | 100 hours |
*Phosphoric acid (0.5%) | Ambient | 100 hours |
1Compatible fluids are defined as those which do not swell, soften or attack any of the filter components.
2 Measured under laboratory test conditions. The actual cumulative time depends on the process conditions. For applications requiring Sterilization or Sanitization Pall recommends the use of Code 7 adaptors to ensure filter sealing after cooling. Cartridges should be cooled to system operating temperature prior to use. Contact Pall for recommended procedures.
Performance
Pressure Drop vs. Liquid Flow Rate3
15 liters per minute @ 100 mbar
2.74 US gpm @ 1 psi
Typical initial clean media differential pressure (ΔP) per 250 mm (10”) cartridge for water at 20 °C (68 °F); viscosity 1 centipoise. For 508, 762 mm and 1016 mm configurations divide the differential pressure by 2, 3, and 4 respectively.
Each 10” element has an effective filtration area of 1m2.
Type
Application
Ordering Information
Part Number: AB [Table 1] FFN [Table 2] W [Table 3]
Table 1: Nominal Length
Code | Description |
1 | 254 mm (10”) |
2 | 508 mm (20”) |
3 | 762 mm (30”) |
4 | 1016 mm (40”) |
Table 2 : Adaptor
Code | Description |
3 | SOE – single open end with flat closed end and external 222 O-rings |
7 | SOE – single open end with fin end 2 locking tabs and external 226 O-rings |
8 | SOE – single open end with fin closure end and external 222 O-rings on open end |
28 | SOE – single open end with fin end, 3 locking tabs and external 222 O-rings |
Table 3: O-ring Seal Material
Code | Description |
H4 | Silicone Elastomer |
J | Ethylene Propylene Rubber |
Segments
检查
Earn 10% off* your next order online by leaving a review of this product. Please login to your account to leave a review. We appreciate and value your feedback.
*Subject to Terms and Conditions.