描述
For Particle Removal
Ultipor GF Plus filter cartridges are made with positive Zeta modified glass fiber media for enhanced filtration efficiency for fluids in the food and beverage industry. In addition to a high particulate removal efficiency and low pressure drop, the positive charge enables the Ultipor GF Plus filter to effectively remove submicron haze particles from a wide variety of aqueous and slightly alcoholic food and beverage products. The single open ended (SOE) configuration is designed to fit into sanitary housings. Ultipor GF Plus filter cartridges are suitable for exposure to repeated hot water and in situ steam sanitization cycles for longer service life.| Features | Benefits |
| Fixed fiber matrix with no adhesives or surfactants |
|
| Pleated media with high dirt holding capacity and positive Zeta potential |
|
| Multiple adaptor options | Easy installation into sanitary housings |
Specifications
Food Contact Compliance
- Food contact compliant filters are available. Please consult the Declarations of Compliance for applicable part numbers at the links below
- Ultipor® GF Plus Filter Cartridges Declaration of Compliance
Materials of Construction
- Filter Medium: Resin bonded glass fibers on a polyester substrate
- Support and Drainage: Polyester
- Core, Cage, End Cap and Fin End: Polypropylene
- Adaptor: Polypropylene with internal stainless steel reinforcing ring
- O-ring Seal: Ethylene propylene rubber or Silicone elastomer
Operating Characteristics in Compatible Fluids11
| Maximum Differential Pressure | Operating Temperature |
| 5.5 bard (80 psid) (forward pressure) | 50 °C (122 °F) |
| 4.1 bard (60 psid) (forward pressure) | 80 °C (176 °F) |
| 300 mbard (4.4 psid) (reverse pressure) | In normal operation or in-situ steam sterilization |
Sterilization and Sanitization
| Media | Temperature | Cumulative Time/30 minute Cycles2 |
| Steam | 125 °C (257 °F) | 25 hours / 50 cycles |
| Hot Water | 85 °C (185 °F) | 25 hours / 50 cycles |
11 Compatible fluids are defined as those which do not swell, soften or attack any of the filter components.
2Measured under laboratory test conditions. The actual cumulative time depends on the process conditions. For applications requiring Sterilization or Sanitization Pall recommends the use of Code 7 adaptors to ensure filter sealing after cooling. Cartridges should be cooled to system operating temperature prior to use. Contact Pall for recommended procedures.
Performance
Quality
- Cartridges produced in a controlled environment
- Manufactured according to ISO 9001:2008 certified Quality Management System
| Media | Particulate Rating (ß-5000) | Pressure Drop vs Liquid Flow Rate3 per 10" element |
| GFHZ | ≤ 1 micron | 10-15 mbar at 10 L/min (0.15 - 0.22 psi at 2.6 US gallons/min) |
| GFNZ | ≤ 2 micron | ~7 mbar at 10 L/min (~0.1 psi at 2.6 US gallons /min) |
3Typical initial clean media differential pressure (dP) per 250 mm (10") cartridge for water at 20 °C (68 °F); viscosity 1 centipoise. For 508, 762 mm and 1016 mm configurations divide the differential pressure by 2, 3, and 4 respectively.
Segments
Beer (Craft/Micro Breweries), Beer (Craft/Micro Breweries), Beer (Corporate), Beer (Corporate), Cider, Juice, Wine
Type
Filter Cartridges
Ordering Information
This information is a guide to the part number structure and possible options. For availability of specific options and housing details, please contact Pall. Example Part Number: AB 4 GF H Z 7 W H4(See bold references in tables below.) Part Number: AB <Length Code from Table 1> GF<Rating Code from Table 2> Z<Adaptor Code from Table 3> W<O-ring Code from Table 4>
Table 1 - Length
| Code | Description |
| 1 | 254 mm (10 in.) |
| 2 | 508 mm (20 in.) |
| 3 | 762 mm (30 in.) |
| 4 | 1016 mm (40 in.) |
Table 2 - Removal Rating
| Code | Description |
| H | ≤ 1 micron |
| N | ≤ 2 micron |
Table 3 - Adaptor
| Code | Description |
| 3 | SOE – single open end with flat closed end and external 222 O-rings |
| 7 | SOE – single open end with fin end, 2 locking tabs and external 226 O-rings |
| 8 | SOE – single open end with fin end and external 222 O-rings |
| 28 | SOE – single open end with fin end, 3 locking tabs and external 222 O-rings |
Table 4 - O-Ring Seal Material
| Code | Description |
| H4 | Silicone Elastomer |
| J | Ethylene Propylene Rubber |
检查
Earn 10% off* your next order online by leaving a review of this product. Please login to your account to leave a review. We appreciate and value your feedback.
*Subject to Terms and Conditions.
