Food Contact Compliance

• Food contact compliant filters are available. Please consult the Declarations of Compliance for applicable part numbers at the links below.
• Please refer to Food Contact Compliance and Safety for a Declaration of Compliance to specific National Legislation and/or Regional Regulatory requirements for food contact use.

Main Constituents

• Cellulose, diatomaceous earth (DE, Kieselguhr), perlite.

Characterization

Grade	Mass per Unit Area g/m2	Thickness mm	Ash %	Water Permeability2 L/m2/min (gal/ft2/min)
FA 05	1350	3.7	46	95 (2.3)
FA 10	1350	3.7	46	146 (3.6)
FA 20	1250	4.0	46	510 (12.5)
FA 30	1250	4.2	46	780 (18.9)

These figures have been determined in accordance with in-house test methods and the methods of the Technical / Analytical Work Group within the European Depth Filtration Association.

²The permeability was measured under test conditions with clean water at 20 °C (68 °F) and a Δp of 1 bar (14.5 psi).

Regeneration

FA series filter sheets may be rinsed with clean water (in the forward or reverse³direction) to increase throughput and to optimize economic efficiency. Optimal regeneration of filter sheets installed in a plate and frame filter may be achieved with serial rinses of warm water followed by hot water. An example protocol is shown below.

1. Rinse with warm water (60 °C / 140 °F) for 15 minutes
2. Rinse with hot water (70 – 80 °C / 158 – 176 °F) for 8 – 10 minutes

³When rinsing in the reverse flow direction it is critical to control particulate and microbial levels in the rinse water so that the filtrate side of the sheet is not contaminated. Water used for reverse flow flushes should be particle-free, and if the filter will not be sterilized prior to re-use the water should be free of microbes. Backwashing should be in a diagonal direction from outlet to inlet in a plate and frame filter.

Sterilization and Sanitization

Method	Temperature °C (°F)	Maximum Differential Pressure bar (psi)	Time4/ Cycle min
Steam	125 (257)	0.5 (7.2)	20
Hot Water	90 (194)	1 (14.5)	30

⁴ The actual time required may vary as a function of the process conditions.

Filtration Guidelines⁵

For achieving optimal filtrate quality, the following flow velocities and differential pressures should not be exceeded:

Grade	Flow Velocity L/m2/h (gal/ft2/h)	Maximum Differential Pressure bar (psi)
FA 05	500 (12.3)	1.5 (21.8)
FA 10	850 (20.9)	3 (43.5)
FA 20	850 (20.9)	3 (43.5)
FA 30	850 (20.9)	3 (43.5)

As the filtrate quality can be impacted by the filtration flow rate, the following table provides further guidelines for sheet selection and flux rate for apple juice concentrate.

Application	Grade	Flow Velocity for Concentrate L/m2/h (gal/ft2/h)	Flow Velocity for Half Concentrate L/m2/h (gal/ft2/h)
Filtration prior to concentration	FA 10	200-250 (4.9-6)	400-500 (9.8-12.3)
Microbial reduction (low bacterial load)	FA 05	200-250 (4.9-6)	400-500 (9.8-12.3)
Microbial reduction (high bacterial load)	FA 05	175-200 (4.3-4.9)	350-400 (8.6-9.8)

⁵Please contact Pall for recommendations on your specific filtration process as results may vary by product, pre-filtration and filtration conditions.

For additional operating guidelines, including rinsing of sheets prior to use, please refer to instructions provided by Pall.

Quality

• Filter sheets produced in a controlled environment
• Manufactured according to ISO 9001:2008 certified Quality Management System

Relative Retention Rating¹

¹ Effective removal performance of filter sheets is dependent on process conditions.

Juice

Filter Sheets

Available Sheet Formats

Rectangular Sheets

• 400 mm x 400 mm (15.8 in. x 15.8 in.)
• 600 mm x 612 mm (23.6 in. x 24.1 in.)